FRENIC LIFT MANUAL PDF

By admin No comments

FRENIC-Lift. FRENICG11S/P11S. FRENICVG7S. User’s Manuals and Technical Information. FRENIC-Multi User’s Manual. FRENIC-Eco User’s. FRENIC-Lift is an inverter designed to drive a three-phase induction motor ( hereafter For details about this product, refer to the FRENIC-Lift User’s Manual that. The FRENIC-Lift Series of exclusive AC Drives for operation of elevators are FRENIC-Lift AC Drives are available in a series with capacities ranging from

Author: Yozshulkree Duzil
Country: Brazil
Language: English (Spanish)
Genre: Photos
Published (Last): 8 October 2015
Pages: 407
PDF File Size: 17.33 Mb
ePub File Size: 10.61 Mb
ISBN: 319-1-62643-914-5
Downloads: 10400
Price: Free* [*Free Regsitration Required]
Uploader: Tauramar

The first letter is an alphabet that identifies its group and the following two letters are numerals that identify each individual code in the group. Put the front cover back in reverse order of. For the braking resistor built-in type, refer to the next page.

FRENIC-Lift | Fuji Electric Global

Doing so could cause fire. Precautions for use Driving a V When driving a V general-purpose motor with an inverter using ex- general-purpose tremely long wires, damage to the insulation of the motor may occur. Lower the temperature around the motor.

Page 29 Follow the procedure below for wiring and configuration of the inverter. How This Manual Is Organized This chapter lists specifications including output ratings, control system, external dimensions and protective functions. Refer to Chapter 2 Section 2. Page 61 L codes: Date of purchase Inquiries for example, point and extent of breakage, uncertainties, failure phenomena, and other circumstances.

Note 2 To protect wiring, insert a molded case circuit breaker MCCB or an earth leakage circuit breaker ELCB with overcurrent protection of the type recommended for the inverter between the commercial power supply and the inverter.

Selecting function code data assigns the corresponding function to [X1] terminals [ X1] to [X8] as listed below. On the bottom are no case fixing screws. Use them in accordance with your system requirements. Contact your Fuji Electric representative. To improve cooling efficiently, you can take the heat sink out of the equipment or the enclosure as shown on the right so that cooling is done both internally and externally this is called “external cooling”.

  74F244 DATASHEET PDF

Page 31 These are provided for the DC link bus powered system. For the inverters with a capacity of 22 kW or below, wait at least 5 minutes; for the inverters with a capacity of 30 kW or above, wait at least 10 minutes. Page 25 Terminal board illustrated in except Figure A. Please do not use it with other products. Keep this manual in a safe place until this product is. When employing external cooling At the shipment time, the inverter is set up for mount inside your equipment or enclosure so that cooling is done all internally.

Increase F26 Motor Sound Carrier frequency. Each part of the product has its own service life that will vary according to the environmental and operating conditions. Refer to Chapter 5, Section 5. Date of purchase Inquiries for example, point and extent of breakage, uncertainties, failure phenomena, and other circumstances Page Page 77 [ 16 ] Run operation error Problem Lirt incorrectly operated the inverter. Doing so could cause failure.

Fuji Electric FRENIC-Lift series Instruction Manual

crenic Using the optional multi-function keypad allows you to start and stop the motor, monitor running status, and switch to the menu mode. If any of these conditions has occurred, either eliminate the abnormal or error factor s and perform tuning again, or contact your Fuji Electric representative.

Accident or injury may result. Take care of the following items during work.

Table of Contents Add to my manuals Add. Check that a mechanical brake is in effect. Name of option Function and application Insert an MC in the power source side of the inverter in order to: Page Name of option Function and application Insert an MC in the power source side of the inverter in order to: U, V and W respectively and that the grounding wires are connected to the ground electrodes correctly. For the tuning procedure, refer to the instruction manual of the option card.

  ELOGIO DE LA DIFICULTAD DE ESTANISLAO ZULETA PDF

FRENIC-Lift is an inverter designed to drive a three-phase induction motor hereafter called an induction motor and a three-phase permanent magnet synchronous motor hereafter called a synchronous motor for exclusively controlling elevating machinery.

No part of this publication may be reproduced or copied without prior written permission from Fuji Electric Co.

Brake control by output current Operation level 0 to ON delay time 0. Page 48 Tuning procedure What follows gives you a tuning procedure of the inverter for a motor using a multi-function keypad option. Designed for Elevating Machinery. For the motor, check the rated values printed on the nameplate of the motor. Wiring For Control Circuit Terminals 2.

Page 9 Select an inverter according to the applicable motor ratings listed in the standard specifications table for the inverter. Megger test of main circuit Use a VDC Megger and shut off the main power supply without fail during measurement. Page 36 Table manuao.

Marks to classify these situations in the torque control column of the function code table on the following pages as shown below. Page 22 3 For inverters with a capacity of mankal kW or above Removing and mounting the cover To remove the front cover, loosen the four fastening screws, hold it with both hands, and lft it upward. In the following description, the inverter has already been installed. Take an attention for this structure to connect wires to main output secondary terminals. Page 54 F codes: