FARGO DTC515 MANUAL PDF

By admin No comments

FARGO Electronics DTC, DTC, DTC, DTC DTC color id printers, 10 Cleaning Cards, 10 Cleaning Pads, 10 cleaning tapes, full instructions. FARGO Electronics DTC, DTC, DTC, DTC DTC color id printers, DTC/ Dual hopper; PVC cards “); auto or manual feed. HID GLOBAL, HID, the HID logo, FARGO, and iCLASS, are .. installed and used in accordance with the instruction manual, may cause.

Author: Moogushakar Gosida
Country: Cambodia
Language: English (Spanish)
Genre: Marketing
Published (Last): 27 April 2010
Pages: 287
PDF File Size: 2.67 Mb
ePub File Size: 14.1 Mb
ISBN: 787-3-23967-268-2
Downloads: 77581
Price: Free* [*Free Regsitration Required]
Uploader: Arashiktilar

Resolving The Dram Memory Error As an alternative to replacing the Main Print Board, the chip U16 can be replaced. Remove the two 2 Circuit Board mounting screws located in the Hopper opening.

If the break occurs after the yellow panel is transferred to the card, reduce the Print EOF by 5. Enter text from picture: Be sure to push down on the cartridge until it clicks into place.

Card Flipper onto the card path or into he Encoder. Select this option to shift the recorded magnetic data to the left-hand side of the card’s Magnetic Stripe.

Delete an area by using the Manuxl Area arrows to select the area, and click on the Delete button. Click on the Send Update button to bring up the Sending Update to Printer dialog, as shown on the next page.

FARGO DTC SPECIFICATIONS Pdf Download.

In this case, rotate the dargo knob counter-clockwise. Replacing the Printhead Assembly continued Compress these 2 springs to remove the Printhead, as shown below. Resolving the Dtx515 wrinkle problems continued Step Procedure Check the Printhead for debris and burrs. Push firmly to ensure both are securely connected. The Default settings for the Lamination Dwell Time and Temperature are preset for factory-recommended card stocks and overlaminate types.

  KURTLARLA KOAN KADNLAR PDF

Do not change this setting. Press Select to save the new value. Internal Card Guide always remains parallel to the card path and that the screws loosened in Step 1 are retightened after each adjustment.

FARGO Electronics DTC500 Series Troubleshooting Manual

This option shifts colors more radically so the colors in the image will more closely match how they appear on screen. It is through this card grid that up to five areas can be defined.

Selecting The Lamination Type If the Film Lamination option is selected, the film lamination is applied to the printed card, then the card is ejected. Updating The Main Firmware Mznual Reviewing The Shift Data Left Select this option to shift the recorded magnetic data to the left-hand side of the card’s Magnetic Stripe. Replacing The Main Board d Remove the two mounting screws at the middle and lower section along the left edge of the circuit board.

Encoding Errors Determine if manuzl Main Board is bad. However, it will work best with a standard resin black Ribbon.

Open the upper module to find the Ribbon Sensor orientation. The arrows point to the screws described in Step 8. Locate the Sensor near the bottom of the Printer. The file name, location, and version will farvo in the Firmware Updater window, as shown on the next page. Along the left edge of the circuit board, remove the two 2 mounting screws at the middle and lower section.

  DATASHEET 24C16 PDF

This is useful in situations that require cards to be readable with insert type readers. Using The Image Position Button Use the Image Position controls to adjust the position of the overall print area to be precisely centered on a card.

Page – Calibrating the Card Lamination Module’s Installing The New Printhead Assembly Specifying the Copies Specifies the number of copies to be printed, as shown above. Use this option to control specific Printer functions. Printing Process Errors Repair the Ribbon. Replacing The Main Board d Note: Using the Encoding Mode option continued See the previous procedure in this section.

Re-install the printing supplies. Reviewing The Orientation Select Portrait to cause the card to print in a vertical orientation. Confirm that the driver is current by checking at: Step Procedure Adjust the Image Position values dhc515 clicking on the Vertical and Horizontal adjustment arrows, as shown below.

The minimum size for an area is.

At this time, the Printer must be prepared to receive the Firmware update file. See the Updating the Printer’s Firmware on page